Free cisco ccna 640-816 exam
Visited 816 times, 1 so far today
640-816 Exam:Interconnecting Cisco Networking Devices Part 2
TestInside 640-816
Cisco 640-816
Interconnecting Cisco Networking Devices Part 2
Q&A Demo
English: www.TestInside.com BIG5: www.Testinside.net GB: www.testking.name
TestInside,help you pass any IT exam!
TestInside 640-816
1. Refer to the exhibit.
A junior network engineer has prepared the exhibited configuration file. What two statements are true of the planned configuration for interface fa0/1? (Choose two.)
A. The two FastEthernet interfaces will require NAT configured on two outside serial interfaces.
B. Address translation on fa0/1 is not required for DMZ Devices to access the Internet. C. The fa0/1 IP address overlaps with the space used by s0/0.
D. The fa0/1 IP address is invalid for the IP subnet on which it resides.
E. Internet hosts may not initiate connections to DMZ Devices through the configuration that is shown. Answer: BE
2. What is the default Local Management Interface frame type transmitted by a Cisco router on a Frame Relay circuit?
A. Q933a B. B8ZS C. IETF D. Cisco E. ANSI
TestInside 640-816
Answer: D
3. Refer to the exhibit. Which statement describes DLCI 17?
A. DLCI 17 describes the ISDN circuit between R2 and R3.
B. DLCI 17 describes a PVC on R2. It cannot be used on R3 or R1.
C. DLCI 17 is the Layer 2 address used by R2 to describe a PVC to R3.
D. DLCI 17 describes the dial-up circuit from R2 and R3 to the service provider. Answer: C
4. Refer to the exhibit. The network shown in the exhibit has just been installed. Host B can access the Internet, but it is unable to ping host C. What is the problem with this configuration?
A. Host B should be in VLAN 13.
B. The address of host C is incorrect.
C. The gateway for host B is in a different subnet than the host is on.
D. The switch port that sends VLAN 13 frames from the switch to the router is shut down.
E. The switch port connected to the router is incorrectly configured as an access port.
TestInside 640-816
Answer: B
5. Refer to the exhibit. The router has been configured with these commands:
hostname Gateway interface FastEthernet 0/0
ip address 198.133.219.14 255.255.255.248
no shutdown
interface FastEthernet 0/1
ip address 192.168.10.254 255.255.255.0
no shutdown interface Serial 0/0
ip address 64.100.0.2 255.255.255.252
no shutdown
ip route 0.0.0.0 0.0.0.0 64.100.0.1
What are the two results of this configuration? (Choose two.)
A. The default route should have a next hop address of 64.100.0.3.
B. Hosts on the LAN that is connected to FastEthernet 0/1 are using public IP addressing.
C. The address of the subnet segment with the WWW server will support seven more servers. D. The addressing scheme allows users on the Internet to access the WWW server.
E. Hosts on the LAN that is connected to FastEthernet 0/1 will not be able to access the Internet without address
TestInside 640-816
translation.
Answer: DE
6. Refer to the exhibit. Two routers have just been configured by a new technician. All interfaces are up. However, the routers are not sharing their routing tables. What is the problem?
A. Split horizon is preventing Router2 from receiving routing information from Router1.
B. Router1 is configured for RIP version 2, and Router2 is configured for RIP version 1. C. Router1 has an ACL that is blocking RIP version 2.
D. There is a physical connectivity problem between Router1 and Router2. E. Router1 is using authentication and Router2 is not.
Answer: B
7. Refer to the exhibit. What can be concluded from the output of the debug command?
A. The output represents normal OSPF operation.
B. The interfaces of two OSPF routers connected to the Border router are in the same subnet.
C. The OSPF router connected to interface Serial0/1 has NOT formed a neighbor relationship with the Border router.
D. A router is connected to interface Serial0/3 of the Border router. The OSPF router ID of the connected router is
TestInside 640-816
the IP address of the connected interface.
Answer: C
8. Refer to the output from the show running-config command in the exhibit. What should the administrator do to allow the workstations connected to the FastEthernet 0/0 interface to obtain an IP address?
A. Apply access-group 14 to interface FastEthernet 0/0.
B. Add access-list 14 permit any any to the access list configuration.
C. Configure the IP address of the FastEtherent 0/0 interface to 10.90.201.1.
D. Add an interface description to the FastEthernet 0/0 interface configuration. Answer: C
9. S0/0 on R1 is configured as a multipoint interface to communicate with R2 and R3 in the hub-and-spoke Frame
Relay topology shown in the exhibit. Originally, static routes were configured between these routers to
TestInside 640-816
successfully route traffic between the attached networks. What will need to be done in order to use RIP v2 in place
of the static routes?
A. Configure the no ip subnet-zero command on R1, R2, and R3.
B. Dynamic routing protocols such as RIP v2 cannot be used across Frame Relay networks.
C. Configure the s0/0 interface on R1 as two subinterfaces and configure point-to-point links to R2 and R3.
D. Change the 172.16.2.0/25 and 172.16.2.128/25 subnetworks so that at least two bits are borrowed from the last octet.
E. Change the network address configurations to eliminate the discontiguous 172.16.2.0/25 and 172.16.2.128/25
subnetworks. Answer: C
10. Refer to the exhibit. HostA cannot ping HostB. Assuming routing is properly configured, what could be the cause of this problem?
TestInside 640-816
A. HostA is not on the same subnet as its default gateway.
B. The address of SwitchA is a subnet address.
C. The Fa0/0 interface on RouterA is on a subnet that can’t be used. D. The serial interfaces of the routers are not on the same subnet.
E. The Fa0/0 interface on RouterB is using a broadcast address. Answer: D
11. Refer to the exhibit. The routers are running RIPv2. Which addressing scheme would satisfy the needs of this network yet waste the fewest addresses?
A. Network 1: 192.168.10.0/26
Network 2: 192.168.10.64/26
Network 3: 192.168.10.128/26
Serial link 1: 192.168.20.0/24
Serial link 2: 192.168.30.0/24
B. Network 1: 192.168.10.0/26
Network 2: 192.168.10.64/28
Network 3: 192.168.10.80/29
Serial link 1: 192.168.10.88/30
Serial link 2: 192.168.10.96/30
C. Network 1: 192.168.10.0/26
Network 2: 192.168.10.64/27
Network 3: 192.168.10.96/28
Serial link 1: 192.168.10.112/30
Serial link 2: 192.168.10.116/30
TestInside 640-816
D. Network 1: 192.168.10.0/27
Network 2: 192.168.10.64/28
Network 3: 192.168.10.96/29
Serial link 1: 192.168.10.112/30
Serial link 2: 192.168.10.116/30
Answer: C
12. Refer to the exhibit. At the end of an RSTP election process, which access layer switch port will assume the discarding role?
A. Switch3, port fa0/1
B. Switch3, port fa0/12
C. Switch4, port fa0/11
D. Switch4, port fa0/2
E. Switch3, port Gi0/1
F. Switch3, port Gi0/2
Answer: C
13. Refer to the exhibit. The Lakeside Company has the internetwork in the exhibit. The administrator would like
to reduce the size of the routing table on the Central router. Which partial routing table entry in the Central router represents a route summary that represents the LANs in Phoenix but no additional subnets?
PassGuide offers free demo for Certification Exams You can check out the interface, question quality and usability of our practice exams before you decide to buy it. We are the only one site can offer demo for almost all products. Download links:http://demo.passguide.com/downloadTestInside 640-816
A. 10.0.0.0/22 is subnetted, 1 subnets
D10.0.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
B. 10.0.0.0/28 is subnetted, 1 subnets
D10.2.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
C. 10.0.0.0/30 is subnetted, 1 subnets
D10.2.2.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
D. 10.0.0.0/22 is subnetted, 1 subnets
D10.4.0.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
E. 10.0.0.0/28 is subnetted, 1 subnets
D10.4.4.0 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
F. 10.0.0.0/30 is subnetted, 1 subnets
D 10.4.4.4 [90/20514560] via 10.2.0.2, 6w0d, Serial0/1
Answer: D
14. Refer to the exhibit. What does STATUS=ACTIVE refer to in the output of the show frame-relay pvc command?
TestInside 640-816
A. The PVC is experiencing congestion.
B. The Frame Relay switch is correctly programmed with the DLCI and is operational.
C. The router is actively broadcasting to establish a link to the Frame Relay switch.
D. The router is connected to the local Frame Relay switch, but not to the far end device. Answer: B
15. The network administrator of the Oregon router adds the following command to the router configuration: ip route 192.168.12.0 255.255.255.0 172.16.12.1. What are the results of adding this command? (Choose two.)
A. The command establishes a static route.
B. The command invokes a dynamic routing protocol for 192.168.12.0. C. Traffic for network 192.168.12.0 is forwarded to 172.16.12.1.
D. Traffic for all networks is forwarded to 172.16.12.1.
E. This route is automatically propagated throughout the entire network.
F. Traffic for network 172.16.12.0 is forwarded to the 192.168.12.0 network. Answer: AC
Exam Description
The 640-816 Interconnecting Cisco Networking Devices Part 2 (ICND2) is the exam associated with the Cisco Certified Network Associate certification. Candidates can prepare for this exam by taking the Interconnecting Cisco Networking Devices Part 2 (ICND2) v1.0 course. This exam tests a candidate’s knowledge and skills required to successfully install, operate, and troubleshoot a small to medium size enterprise branch network. The exam covers topics on VLSM and IPv6 addressing; extending switched networks with VLANs; configuring, verifying and troubleshooting VLANs; the VTP, RSTP, OSPF and EIGRP protocols; determining IP routes; managing IP traffic with access lists; NAT and DHCP; establishing point-to- point connections; and establishing Frame Relay connections.
Exam Topics
The following topics are general guidelines for the content likely to be included on the Interconnecting Cisco Networking Devices Part 2 exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.
Configure, verify and troubleshoot a switch with VLANs and interswitch communications
Describe enhanced switching technologies (including: VTP, RSTP, VLAN, PVSTP, 802.1q)
Describe how VLANs create logically separate networks and the need for routing between them
Configure, verify, and troubleshoot VLANs
Configure, verify, and troubleshoot trunking on Cisco switches
Configure, verify, and troubleshoot interVLAN routing
Configure, verify, and troubleshoot VTP
Configure, verify, and troubleshoot RSTP operation
Interpret the output of various show and debug commands to verify the operational status of a Cisco switched network
Implement basic switch security (including: port security, unassigned ports, trunk access, etc.)
Implement an IP addressing scheme and IP Services to meet network requirements in a medium-size Enterprise branch office network
Calculate and apply a VLSM IP addressing design to a network
Determine the appropriate classless addressing scheme using VLSM and summarization to satisfy addressing requirements in a LAN/WAN environment
Describe the technological requirements for running IPv6 (including: protocols, dual stack, tunneling, etc)
Describe IPv6 addresses
Identify and correct common problems associated with IP addressing and host configurations
Configure and troubleshoot basic operation and routing on Cisco devices
Compare and contrast methods of routing and routing protocols
Configure, verify and troubleshoot OSPF
Configure, verify and troubleshoot EIGRP
Verify configuration and connectivity using ping, traceroute, and telnet or SSH
Troubleshoot routing implementation issues
Verify router hardware and software operation using SHOW & DEBUG commands
Implement basic router security
Implement, verify, and troubleshoot NAT and ACLs in a medium-size Enterprise branch office network.
Describe the purpose and types of access control lists
Configure and apply access control lists based on network filtering requirements
Configure and apply an access control list to limit telnet and SSH access to the router
Verify and monitor ACL’s in a network environment
Troubleshoot ACL implementation issues
Explain the basic operation of NAT
Configure Network Address Translation for given network requirements using CLI
Troubleshoot NAT implementation issues
Implement and verify WAN links
Configure and verify Frame Relay on Cisco routers
Troubleshoot WAN implementation issues
Describe VPN technology (including: importance, benefits, role, impact, components)
Configure and vary PPP connection between Cisco routers
Recommended Training
The following courses are the recommended training for this exam.
Interconnecting Cisco Networking Devices Part 2 (ICND2) v1.0
Exam Number/Code: 640-816
Exam Name: Interconnecting Cisco Networking Devices Part 2
Updated:March 20th , 2008
Questons and Answers : 147 Q&As
Exam Language(s): English
Price: $ 99.99
freedown1:Free Latest cisco 640-816 exam
freedown2:Free Latest cisco 640-816 exam
freedown3:Free Latest cisco 640-816 exam
password:www.certbible.org
Dowload PassGuide Practice Test Questions
8 Comments on “Free cisco ccna 640-816 exam”
I like the way it was put: general guidelines. It